Klass Kote two part Epoxy Paint PART B Catalyst

Description

For new painters; Epoxy systems requires 2 parts: A" and "B" mixed equally. We use this paint on RC nitro airplanes and RC nitro Boats. It is DURABLE and works great!
!
DESCRIPTION
KLASS KOTE is a series of two-component epoxy coatings available in a variety of colors, primers, and clear. It is quick air-drying, chemical hardening, and thermosetting.  It can be forced dried to accelerate cure.  The dried film is very attractive, tough, durable, as well as flexible. It provides excellent adhesion on a wide variety of substrate.
BASIC USES
KLASS KOTE has been field tested since 1964 on many different substrates including steel, aluminum, masonry, wood, wood composition boards and several other substrates.
PHYSICAL DATA
Note *** (based on White #100 with Gloss Catalyst #405)
SOLIDS BY WEIGHT     56.23%
SOLIDS BY VOLUME     44.94%
SURFACE PREPARATION
The surface must be clean and free from dirt, dust, grease, rust, and scale, or anything that will otherwise impede adhesion. Whenever possible, solvent wash with KLASS KOTE EPOXY REDUCER #500. If the recommended reducer is not available, use a high-grade lacquer thinner.
APPLICATION
KLASS KOTE products work ideally with conventional air-atomizing spray equipment, as well as HVLP and airless equipment, and can also be applied with a brush or roller. If you choose to apply Klass Kote Epoxy with a brush - choose a high-quality, natural bristle brush. Once the components are mixed and reduced, KLASS KOTE covers like most conventional finish coats. Film thickness should be built up by applying successive thin coats of paint and allowing about 20 minutes "flash off" time between coats.
For electrostatic application, if conductivity does not fall within the prescribed range for a given application the conductivity can be raised by adding a polar solvent, such as PPG DTL 16 or Klean-Strip L-27.  The polar solvent may have to be added a number of different times in a number of different quantities before desired conductivity is reached, so be sure to record the amount added to each test batch before application.
MIXING INSTRUCTIONS
Thoroughly mix equal parts by volume of components A & B. Allow mixture to induct/react for 30 to 40 minutes, (with occasional stirring) prior to application. Always mix equal parts by volume of epoxy and catalyst components together first --before reducing the mixture. The amount of reducer needed depends upon ambient temperature and type of spray equipment used. For finish coat, start with 6 parts paint to 1 part KLASS KOTE EPOXY REDUCER #500. If KLASS KOTE REDUCER is unavailable, use a high-grade lacquer thinner formulated to reduce epoxies. Reduction up to 1-to-1-to-1 (1-part A, 1-part-B, & 1-part Reducer) may be necessary to achieve the proper viscosity -- especially when working with smaller guns and air brushes.  Do NOT over-reduce!
CURE SCHEDULE
For best results paint and surface should be over 70° F. Klass Kote Epoxy can be force dried after the solvent has been flashed off. Suggest 120°F for 15 minutes to speed cure time.
At 70°F (air & substrate temperatures):
TACK FREE TIME:             20-30 MINUTES
PRINT FREE TIME:           4 HOURS
PACKAGING TIME:            24 HOURS
RECOAT WINDOW:           1 – 24 HOURS (DEPENDING ON SHOP CONDITIONS)
SWARD HARDNESS:          4 DAYS - 1 WEEK
COVERAGE
Using conventional air atomizing spray equipment on a non-porous substrate, 1 quart of reduced KLASS KOTE will cover approximately 75-100 square feet. On more porous substrates, 1 quart will cover approximately 60 square feet.
Note this paint must go UPS ground.  So NO PO Boxes, Cont. USA ONLY.
The .50 is the minimum shipping price.  Other sizes or quantities will be a littel higher, please email for a quote.  Request an invoice at check out so we can adjust your shipping.
We do not overcharge for shipping, just what the real price is.   I will refund any extra shipping.
Please email us with any questions.  For new painters; Epoxy systems requires 2 parts: A" and "B" mixed equally. We use this paint on RC nitro airplanes and RC nitro Boats. It is DURABLE and works great!
!